ospf的高级应用之rip(H3C)案例一：1作业要求：把rip学到的路由重分发到ospf中在rip中注入默认路由指向ospf实现路由汇总(在ABR上汇总)配置末梢区域配置完全末梢区域2.拓扑图3.设备介绍:交换机：HUAWEIQUIDWAYS2000serialsHYPERLINK"http://www.2cto.com/net/router/"\t"_blank"路由器：HUAWEIQUIDWAYR26214.设备配置：www.2cto.comHYPERLINK"http://www.2cto.com/net/switch/"\t"_blank"交换机的配置：[Quidway]vlan10[Quidway-vlan10]descriptionin[Quidway-vlan10]porte0/3toe0/6[Quidway-vlan10]quit[Quidway]intVlan-interface10[Quidway-Vlan-interface10]ipadd192.168.1.1255.255.255.0[Quidway]vlan20[Quidway-vlan20]descriptionout[Quidway-vlan20]porte0/1[Quidway-vlan20]quit[Quidway]intvlan20//进vlan[Quidway-Vlan-interface20]ipadd192.168.2.1255.255.255.0//配IP[Quidway-Vlan-interface20]quit[Quidway]ospf//模式请注意：[Quidway-ospf]area2//进入要宣告网络的区域[Quidway-ospf-area-0.0.0.2]network192.168.1.00.0.0.255//宣告网络[Quidway-ospf-area-0.0.0.2]network192.168.2.00.0.0.255路由器R3的配置：www.2cto.com[R3]inte1[R3-Ethernet1]ipadd192.168.2.2255.255.255.0[R3-Ethernet1]ints0[R3-Serial0]ipadd192.168.3.1255.255.255.0[R3-Serial0]quit[R3]ospfenable//启用OSPF协议[R3]ints0//进接口启用ospf（所有接口都要启用）[R3-Serial0]ospfenablearea0[R3-Serial0]inte1[R3-Ethernet1]ospfenablearea2路由器R10的配置：www.2cto.com[R10]ints0[R10-Serial0]ipaddress192.168.3.224[R10-Serial0]ints1[R10-Serial1]ipadd192.168.4.124[R10-Serial1]inte1[R10-Ethernet1]ipadd192.168.5.124[R10]ospfenable[R10]ints1[R10-Serial1]ospfenablearea1[R10-Serial1]ints0[R10-Serial0]ospfenablearea0[R10]rip//启动rip协议[R10-rip]network192.168.5.0[r10]ints0//串行口的最后一端要复位！[r10-Serial0]shutdown[r10-Serial0]undoshutdow路由器R5的配置：[R5]ints1[R5-Serial1]ipadd192.168.4.224[R5]intloo1www.2cto.com//由于未接线，所以设置loopback接口[R5-LoopBack1]ipadd192.168.8.124//主地址[R5-LoopBack1]ipadd192.168.9.124sub//配置辅助IP地址(为了实现路由汇总)[R5-LoopBack1]ipadd192.168.10.124sub[R5-LoopBack1]ipadd192.168.11.124sub[R5-LoopBack1]quit[R5]ints1[R5-Serial1]ospfenablearea1[R5-Serial1]intlo1[R5-LoopBack1]ospfenablearea1[R5]ints1www.2cto.com[R5-Serial1]shut[R5-Serial1]undoshut路由器R9的配置：[Rou